Kingwood Underground
the heart and soul of our Kingwood, Texas family
Login - Create Account - Help
Clean out your garage on Kingwood bookoo! Or find local garage sales on Yard Sale Search.com
KU Live!

Boat repair question

who's talking here?

Melanie 1
MonzaRacer 2
Fin and Feather 3
offroad4by4 1

     » send to friend     » save in my favorites     » flag dangerous topic flag as a dangerous topic

Fin and Feather --- 17 years ago -

(yes i know its a long shot, but you never know) I have recently acquired an boat that might have a pinhole leak on the inner (metal) gas tank, my question is can you coat the inside of the tank with some kind of epoxy to seal it off and protect it from future problems?  

offroad4by4 --- 17 years ago -

Good luck with this one. Is this an inboard gas tank? My experience unfortunately has been if the the leak originated from the inside, the remaining portion of the tank is in about the same shape and ready to begin leaking. My leak was on the bottom side of the tank where water was able to pool, and the leaks just cascaded over time (aluminum tank too go figure). The cost of tearing up the floor (plywood floor and not the fiberglass floor) was astronomical compared to the cost of the new tank. Here are a few people to call (bit of a drive for repair but worth it) that might have better insight (Fiberglass Work - Larry (936) 449-6812, K&D Marine (936) 449-4476). I have heard good things about the boat repair shop across the Atascocita bridge on the North Side, but he is so backed up usually if you do have to leave your boat. If its a portable tank and you can get to the leak easily, JB Weld always held great on our tractor tanks. Good Luck. 

Fin and Feather --- 17 years ago -

Luckily this one has an access panel for easier access but ½ of it is under my console, uggh..i can only imagine how much fun its going to be with all the wires going everywhere.. The original owner suspected it to leak some time back and instead of looking into it he just used external tanks as a quick fix. I’m interested in the extra foot room so thinking about pulling it next week when I’m down there replacing the throttle cables. It looks like we are on the same page with fixing it though so far all I could come up with is ether using, belzona, jb wield, or maybe just replacing the bottom section if that’s all that is pitted. But who knows what it’s going to look like 

MonzaRacer --- 17 years ago -

FandF...they make products to "reline" tanks. Kreem Fuel Tank Liner is one, but not sure if it is sold locally. May have to go to JCWhitney or other supplier. From their website... SURFACE PREPARATION: It is critical that the inside of the tank have an oil-free surface without rust to insure proper adhesion. We recommend Kreem Tank-Prep Kit A & B, our two part system for rust removal and metal etching. 1. Wash out tank with hot soapy water. If the tank if badly rusted and has loose flaky rust add stones or nuts and bolts and agitate to remove the loose rust. For new tanks it is important to remove the oily protective coating. An industrial strength detergent, or a commercial degreaser/cleaner like KREEM’s new Tank Cleaner/Degreaser, acetone, M.E.K. should be used. 2. After completing step 1, and to obtain maximum adhesion, the surface rust should be removed and the metal surface etched, this can be accomplished by using Kreem Tank Prep A & B Kit, or some other acid based rust remover that also etches metal. Repeat if necessary until all rust is removed. 3. Rinse tank with water until all traces of Tank-Prep A (acid etch) are removed. Drain out excess water. Using Tank-Prep B (acetone or M.E.K.) rinse thoroughly removing trace amounts of water. CAUTION: these chemicals are flammable. The tank is now ready for immediate coating. APPLICATION 1. Shake or stir well before use. Keep container tightly closed when not in use. Stop all outlets except fill spout. 2. Pour Liner into tank and coat entire inner surface by slowly rotating tank in all directions.When all surfaces have been completely coated, a generous excess should remain. Let tank stand for 8-10 minutes with spout open, then close spout and slowly rotate tank allowing excess to re-coat all surfaces. Let tank stand for an additional 8-10 minutes with spout open however, this time on a different side. Repeat this until the tank has the desired coating. Do not allow coating to drain to one area and dry. Drain off excess coating for later use. 3. Drain any excess, remove all stops and allow to air-dry in a well ventilated area for at least 24 hours. A nozzle from a low pressure air compressor blowing lightly into the fuel spout and out another opening will greatly reduce setup time. 4. For extra protection, air-dry first coat for 6 hours or longer and repeat step 2 of application process. 

Fin and Feather --- 17 years ago -

Have you ever used it? I picked up some once for about $50 then returned it after finding a new tank for 28. I didn’t know you could use this on larger tanks also.. you can get one kit for each 20gal of tank 

MonzaRacer --- 17 years ago -

Have you ever used it? No, I've not used it. I had a tank go bad once, but it was only a 6 gal tank and easier to just get a new one. 

Melanie --- 17 years ago -

We use James @ Holliday Marine. He is in Huffman right off 1960. Very reasonable & fair guy. Here's his info: BUSINESS HOURS MON-FRI - 9AM - 6PM SAT - 9AM - 2PM 281 324 6739 FAX: 281 324 3379 HOLLIDAYMARINE@gmail.com 24207 ANDERSON ST HUFFMAN, TX 77336 

page 1
Login to add your comments!

see more discussions about...


Online now:
hit counters

Terms of Service - Privacy Policy - Ice Box

Kingwood Underground